Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me.
Smart Drives Senior Member Joined: 06/07/2009 Location: AustraliaPosts: 115
Posted: 08:33am 20 May 2010
Copy link to clipboard
Print this post
I am selling all my motors rewired or not , $10 each + freight $20..
just specify if you want 60S or 80S. no 60dc decogged (by factory) left.
two Xantrex C40 controllers. $250 each + freight $10
I have 3 x 90m lengths of 25mm2 copper wire. $220 each
I will post more at a later date.
We are moving down the coast and i only have room for 1 48v system.
Cam.
smartdrivesaustraliaATgmail.comAll smart drive parts sold
Custom built turbine parts on
Multicam flatbed CNC Router
VK4AYQ Guru Joined: 02/12/2009 Location: AustraliaPosts: 2539
Posted: 12:12pm 20 May 2010
Copy link to clipboard
Print this post
Hi Cam
I would like two 80 motors for a later project and am looking for a LG motor if you have one.
All the best
BobFoolin Around
Smart Drives Senior Member Joined: 06/07/2009 Location: AustraliaPosts: 115
Posted: 04:34am 22 May 2010
Copy link to clipboard
Print this post
If anyone is nearby i have 24 x 300 amp/h batteries, i am using them at the moment
for lighting in the house. $15 each
I have 3 x 11m high (in 2 pieces) poles with 8mm cables (x3)3mm cable (x3) & and baseplate. 100mm dia. & 60mm dia. pickup only $200 each
Short black high speed blades $20 each
2.5m dia. fibreglass blades (jaycar) $150 for 3 (2 sets)very good blades.
1 set of Chinese fibreglass blades 2.1m dia. $150
2 chinese 12v motors ,work well $80 each
1 60DC MOTOR LEFT it has been rewired $50 (factory decogged)
2 100S motors left $50 each
more to come..
Cam.All smart drive parts sold
Custom built turbine parts on
Multicam flatbed CNC Router
Hi Cam
I would like to buy 2x 100s and 4x 80s if you let me know how much with frieght to North Haven I'll get the money into your acc.
Thanks
Marty.HCan't do it we'll show them a thing or two
Smart Drives Senior Member Joined: 06/07/2009 Location: AustraliaPosts: 115
Posted: 09:29am 08 Jun 2010
Copy link to clipboard
Print this post
Marty,
i can only post two motors at once or they say its too heavy.
so $90 will get the 4 80S motors to you and $105 will get the
two 100s motors to you.
Bob,
i will hold the other two 100s for you , your freight is a bit dearer
$115-
Thanks.
Cam.
All smart drive parts sold
Custom built turbine parts on
Multicam flatbed CNC Router
matt down south Regular Member Joined: 20/10/2007 Location: AustraliaPosts: 50
Posted: 03:57pm 08 Jun 2010
Copy link to clipboard
Print this post
hi Cam
any 100's motor left?and the slip rings?
thanks mattmatt
Smart Drives Senior Member Joined: 06/07/2009 Location: AustraliaPosts: 115
Posted: 04:52am 10 Jun 2010
Copy link to clipboard
Print this post
Hi Matt,
No 100S motors left and i have to wait and see if brucedownunder
wants the slip rings otherwise they are yours.
Cam.
All smart drive parts sold
Custom built turbine parts on
Multicam flatbed CNC Router
brucedownunder2 Guru Joined: 14/09/2005 Location: AustraliaPosts: 1548
Posted: 10:15pm 10 Jun 2010
Copy link to clipboard
Print this post
Thanks Cam ,,
Matt can have the sliprings, thanks for the thought,I should have got back to you earlier,sorry.
BruceBushboy
Smart Drives Senior Member Joined: 06/07/2009 Location: AustraliaPosts: 115
Posted: 03:16am 15 Jun 2010
Copy link to clipboard
Print this post
I am sending your motors today.
Cam.
All smart drive parts sold
Custom built turbine parts on
Multicam flatbed CNC Router
dwyer Guru Joined: 19/09/2005 Location: AustraliaPosts: 574
Posted: 10:21pm 16 Jun 2010
Copy link to clipboard
Print this post
Hi Cam
Have you got windmill tower and chinse blades for sale?
About Tower can you give me information about the height? as saw it some where in this forum but who from ??
Dwyer
Smart Drives Senior Member Joined: 06/07/2009 Location: AustraliaPosts: 115
Posted: 02:11am 17 Jun 2010
Copy link to clipboard
Print this post
Hi Dwyer,
Yes i have , where are you located ?
tower 1 is in two pieces bolted together
tower 2 is in 3 slip in pieces
both are 4m high i think and come with base plates.
Cam.
All smart drive parts sold
Custom built turbine parts on
Multicam flatbed CNC Router
dwyer Guru Joined: 19/09/2005 Location: AustraliaPosts: 574
Posted: 12:31pm 17 Jun 2010
Copy link to clipboard
Print this post
Hi Cam
I am at Upper Lockyer pc 4352 near Toowoomba so what is total full length as need go over 9 metre as got couple large roll high tensile cables (plenty of them) suit for my tower however l am looking at your tower see if l able to add up with my tower still on the ground
Dwyer
Smart Drives Senior Member Joined: 06/07/2009 Location: AustraliaPosts: 115
Posted: 08:58am 18 Jun 2010
Copy link to clipboard
Print this post
They dont sound like they will be suitable,
but i have one set of chinese blades and hub if you want them.
$150 plus freight (approx $30)
Cam.
All smart drive parts sold
Custom built turbine parts on
Multicam flatbed CNC Router
Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me.
Print this post
