 Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me. |
Forum Index : Microcontroller and PC projects : New MAXIMITE
| Author | Message | ||||
vk4tec Senior Member  Joined: 24/03/2012 Location: AustraliaPosts: 239 |
Hello From getting it in the mail to firmware flash and first program in about an hour. Happy vegemite Maximite ex Altronics - Andrew - Andrew Rich VK4TEC www.tech-software.net |
||||
| Bugs2 Newbie  Joined: 18/05/2012 Location: United KingdomPosts: 29 |
well, your doing better than me! I'm still having problems trying to reprogramme a DuinoMite-Mini with the latest version of MMBasic. Not sure whether its me (most likely)or documentation errors. Please could you do a step-by-step guide for the rest of us? |
||||
| vk4tec Senior Member Joined: 24/03/2012 Location: AustraliaPosts: 239 |
How to re-flash a DuinoMite Mini Remove all power from the board Ensure the jumper EXT / USB is across "USB" Now connect the USB cable to the board You should have red LED and yellow LED ON Hold down the reset button ( black ) AND then press the user button ( cream ) Keep holding down the USR ( cream button ) and release the black reset button. As soon as you release the reset button, yellow and green LED flash back and forth Run program "HIDprogrammer.exe" USB bootloader V2.90a for Olimex Boards Program should say "Device Attached" "Connecting...." "Device Ready" Files "import Firmware Image" Select .hex file containing image. Says "Opened: DuinoMite_MMBasic_V3.2A.hex" Now "Program" , "Erase/Program/Verify" device LED will stop flash, then flash some more Bar will progress // Starting Erase/Program/Verify Sequence. Do not unplug device or disconnect power until the operation is fully complete. Erasing Device... (no status update until complete, may take several seconds) Erase Complete (3.172s) Writing Device Program Memory... Writing Complete (6.109s) Verifying Device's Program Memory... Verifying Complete (141.469s) Erase/Program/Verify Completed Successfully. You may now unplug or reset the device. // Now reset ( black button ) and exit program LED stop flashing, just yellow and red LED - Andrew - Andrew Rich VK4TEC www.tech-software.net |
||||
donmck Guru  Joined: 09/06/2011 Location: AustraliaPosts: 1313 |
Thanks Andrew, have added your explanation to the bottom of: http://www.duinomite.com/duinomite-firmware-update-guide/ Hopefully this will assist users still having problems with this procedure. Cheers Don... https://www.dontronics.com |
||||
djuqa Guru Joined: 23/11/2011 Location: AustraliaPosts: 447 |
Ditto details posted on duinomite.com.au VK4MU MicroController Units |
||||
| donmck Guru Joined: 09/06/2011 Location: AustraliaPosts: 1313 |
David, none of your sig links are correct. Cheers Don... https://www.dontronics.com |
||||
| djuqa Guru Joined: 23/11/2011 Location: AustraliaPosts: 447 |
they are now thanks VK4MU MicroController Units |
||||
| Bugs2 Newbie Joined: 18/05/2012 Location: United KingdomPosts: 29 |
Many thanks vk4tec for that detailed explanation. I can see where some original bits of documentation may have lead me astray, but will now have another go and let you know how it goes. |
||||
| Bugs2 Newbie Joined: 18/05/2012 Location: United KingdomPosts: 29 |
Just tried reprogramming by following vK4tec's very clear instructions and every stage worked just fine! Thanks again. |
||||
| donmck Guru Joined: 09/06/2011 Location: AustraliaPosts: 1313 |
Great news Mike, glad you eventually got there, and also verified that Andrew's instructions must be spot on. Cheers Don... https://www.dontronics.com |
||||
 Print this page |
