Home
JAQForum Ver 24.01
Log In or Join  
Active Topics
Local Time 23:45 25 Nov 2024 Privacy Policy
Jump to

Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me.

Forum Index : Microcontroller and PC projects : New Version of MMBasic. Version 3.2A

Author Message
Geoffg

Guru

Joined: 06/06/2011
Location: Australia
Posts: 3194
Posted: 06:30am 04 May 2012
Copy link to clipboard 
Print this post

A new version of MMBasic (ver 3.2A) is available for download from http://geoffg.net/maximite.html#Downloads

This is a minor update that fixes a few bugs mostly associated with drive A: and the serial ports on the DuinoMite. The Change Log (included in the update download) details the changes.

Geoff
Geoff Graham - http://geoffg.net
 
vk4tec

Senior Member

Joined: 24/03/2012
Location: Australia
Posts: 239
Posted: 11:10am 04 May 2012
Copy link to clipboard 
Print this post

Works for me

NMEA PARSE
LCD 20x4
SD card write
MOD-GPS
SETTICK
MATHS
USERBTN

All ok

- Andrew -
Andrew Rich VK4TEC
www.tech-software.net
 
donrecardo
Newbie

Joined: 04/05/2012
Location: United Kingdom
Posts: 16
Posted: 04:08pm 04 May 2012
Copy link to clipboard 
Print this post

  Geoffg said   A new version of MMBasic (ver 3.2A) is available for download from http://geoffg.net/maximite.html#Downloads

This is a minor update that fixes a few bugs mostly associated with drive A: and the serial ports on the DuinoMite. The Change Log (included in the update download) details the changes.

Geoff


Hi Geoff
I, and another person I met both found a problem using MMBasic for dos .
If you set auto line numbering with
auto 10,10
it works fine , but when you want to end auto numbering and type "run" to try the code
there is a problem . CTRL C does not break you out of auto numbering.
I tried again using your new updated version of MMBasic but its still the same .

Is CTRL C the correct way to exit from auto line number or is it another key combination?

DonEdited by donrecardo 2012-05-06
 
vk4tec

Senior Member

Joined: 24/03/2012
Location: Australia
Posts: 239
Posted: 12:40am 05 May 2012
Copy link to clipboard 
Print this post

Andrew Rich VK4TEC
www.tech-software.net
 
Geoffg

Guru

Joined: 06/06/2011
Location: Australia
Posts: 3194
Posted: 01:31am 05 May 2012
Copy link to clipboard 
Print this post

  donrecardo said  I, and another person I met both found a problem using MMBasic for dos. If you set auto line numbering with auto 10,10 it works fine, but when you want to end auto numbering and type "run" to try the code there is a problem. CTRL C does not break you out of auto numbering.


Ah, that was a small bug in the DOS version only. I have fixed it now so please download the DOS version again and CTRL-C should work OK.

Geoff
Geoff Graham - http://geoffg.net
 
donmck

Guru

Joined: 09/06/2011
Location: Australia
Posts: 1313
Posted: 04:19am 05 May 2012
Copy link to clipboard 
Print this post

  vk4tec said  


Thanks very much Andrew, hAVE ADDED IT TO:
http://www.dontronics-shop.com/maximite-12pin-dm-mini.html

Cheers Don...
https://www.dontronics.com
 
donrecardo
Newbie

Joined: 04/05/2012
Location: United Kingdom
Posts: 16
Posted: 09:09am 05 May 2012
Copy link to clipboard 
Print this post

  Geoffg said  
  donrecardo said  I, and another person I met both found a problem using MMBasic for dos. If you set auto line numbering with auto 10,10 it works fine, but when you want to end auto numbering and type "run" to try the code there is a problem. CTRL C does not break you out of auto numbering.


Ah, that was a small bug in the DOS version only. I have fixed it now so please download the DOS version again and CTRL-C should work OK.

Geoff


Thanks Geoff
It works fine now

Don
 
vk4tec

Senior Member

Joined: 24/03/2012
Location: Australia
Posts: 239
Posted: 08:44am 08 May 2012
Copy link to clipboard 
Print this post

Running MMBasic V3_2A in new DuinoMite Mega

Dropped in SD card - power up

Flashed

Works fine

- Andrew -
Andrew Rich VK4TEC
www.tech-software.net
 
Print this page


To reply to this topic, you need to log in.

© JAQ Software 2024