Home
JAQForum Ver 24.01
Log In or Join  
Active Topics
Local Time 15:00 22 Nov 2024 Privacy Policy
Jump to

Notice. New forum software under development. It's going to miss a few functions and look a bit ugly for a while, but I'm working on it full time now as the old forum was too unstable. Couple days, all good. If you notice any issues, please contact me.

Forum Index : Microcontroller and PC projects : Level shifter

Author Message
Plasmamac

Guru

Joined: 31/01/2019
Location: Germany
Posts: 554
Posted: 07:36am 22 Oct 2024
Copy link to clipboard 
Print this post

What level shifter is the best for using on the Picomite?
Plasma
 
PhenixRising
Guru

Joined: 07/11/2023
Location: United Kingdom
Posts: 853
Posted: 08:03am 22 Oct 2024
Copy link to clipboard 
Print this post

  Plasmamac said  What level shifter is the best for using on the Picomite?


If uni-direction, I like the 74HC4050


74HC4050.pdf
 
Volhout
Guru

Joined: 05/03/2018
Location: Netherlands
Posts: 4213
Posted: 08:10am 22 Oct 2024
Copy link to clipboard 
Print this post

This works as well for I2C and signals up to few hundred kHz.



Volhout
PicomiteVGA PETSCII ROBOTS
 
Marcel27

Regular Member

Joined: 13/08/2024
Location: Netherlands
Posts: 53
Posted: 11:18am 22 Oct 2024
Copy link to clipboard 
Print this post

Double entry ..... link
Edited 2024-10-22 21:19 by Marcel27
If you use AI, you lose your mind.
 
Mixtel90

Guru

Joined: 05/10/2019
Location: United Kingdom
Posts: 6761
Posted: 12:40pm 22 Oct 2024
Copy link to clipboard 
Print this post

If you only need two channels then I've found that 2 mosfets and four resistors can often be squeezed into spaces that you wouldn't expect them to fit. Mind you, I've put one of those suggested by Volhout between the legs of a Pico. :)

For shifting downwards only, a simple potential divider often works.
Edited 2024-10-22 22:42 by Mixtel90
Mick

Zilog Inside! nascom.info for Nascom & Gemini
Preliminary MMBasic docs & my PCB designs
 
Martin H.

Guru

Joined: 04/06/2022
Location: Germany
Posts: 1113
Posted: 03:15pm 22 Oct 2024
Copy link to clipboard 
Print this post

I have successfully used ZVNL110A for PS2 Level shift so far
'no comment
 
stanleyella

Guru

Joined: 25/06/2022
Location: United Kingdom
Posts: 2109
Posted: 05:19pm 22 Oct 2024
Copy link to clipboard 
Print this post

I used 8 channel bi-direction level inverter with arduino and ili9341 as arduino 5v logic and ili 3.3v
their cheap and should be ok to raise 3.3v logic to 5v
 
Plasmamac

Guru

Joined: 31/01/2019
Location: Germany
Posts: 554
Posted: 11:23am 23 Oct 2024
Copy link to clipboard 
Print this post

Thx for all ,

@stanleyella link please
Plasma
 
stanleyella

Guru

Joined: 25/06/2022
Location: United Kingdom
Posts: 2109
Posted: 02:55pm 23 Oct 2024
Copy link to clipboard 
Print this post

  Plasmamac said  Thx for all ,

@stanleyella link please

bought years ago, something like this. 8 fets, marked LV and HV, LV is 3.3 device, HV is 5V device
https://www.ebay.co.uk/itm/192441573509
 
stanleyella

Guru

Joined: 25/06/2022
Location: United Kingdom
Posts: 2109
Posted: 06:40pm 23 Oct 2024
Copy link to clipboard 
Print this post

what's it for?
 
Marcel27

Regular Member

Joined: 13/08/2024
Location: Netherlands
Posts: 53
Posted: 05:23am 24 Oct 2024
Copy link to clipboard 
Print this post

I use most of the time a voltage devider for low speed or BS170 for 2-way or an optocoupler for 1-way communication. I've a lot of optocouplers lying around and work fine.
If you use AI, you lose your mind.
 
Print this page


To reply to this topic, you need to log in.

© JAQ Software 2024